salaryyacht4

Reasons Your Fiat 500 Key Fob Won't Work A key fob for Fiat 500 allows you to easily open doors and start your car. There are many reasons the fob could stop working. This could be due to a dead battery and water damage, as well as issues with the receiver module, and interference. This listing is for an NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It has to be professionally programmed (click here to search for local automotive locksmiths). It comes with lock, unlock and trunk buttons. Dead Coin Battery A dead battery is probably the most common cause of your 500 key fob not functioning. Key fobs of today have only a limited range of operation and must be within a few inches of the vehicle to work. If you're far from your vehicle, and you press the key fob button the car will not respond, and will display an “Key Fob Not Detected” message in the instrument cluster. If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a fresh one of a trusted brand such as Panasonic Duracell or Energizer. You can find them in your local hardware store or online. You can test the battery in the coin-cell by pressing the buttons while standing close to your Fiat 500. The parking lights should flash and the key fob will operate the lock and unlock switches. If your key fob still isn't working after replacing the battery, there might be water damage that hinders it from interacting with the module inside your vehicle. Water damage can happen in many ways, such as a simple splash or submerging the key fob saltwater at the beach. If you suspect that your fob was exposed to water, try placing it in a dry rice bag to draw the moisture out. If this does not work, you'll need to have your fob reprogrammed either by an auto locksmith or a dealer. Water Damage Damage to the water supply can occur if you submerge the fob in the ocean, or wash it in a washer. Saltwater can be particularly harmful to the fob's circuit board, causing it to short out and eventually end up dying. If you get the fob wet, it's not an option but if you accidentally drop it in a glass of water or forget to remove it from your pants pocket before running the washer Don't give up hope. Take the battery off first. Before replacing the battery, clean the electronic chip with isopropyl, or a similar product. Test the fob afterward to determine if it's functioning. If the fob doesn't work, it may have to be changed. This is usually handled by a dealer or professional auto locksmith. If the key you have is older and has not been programmed for your vehicle, you will need to replace it completely. A professional locksmith for automotive can do this job. The locksmith will require the key cut to match your vehicle's ignition. The locksmith also needs to reprogram the fob into the car's system. This is a cost-effective and quick process that can be completed on the same day. Receiver Module Issues One of the simplest reasons why your 500 key fob might stop functioning is because it's out of range. The remote has a maximum range of 30 feet. Therefore, if you are too far from your car it won't respond to your commands. It can be solved by moving closer to your vehicle until it starts responding. If fiat 500 key doesn't work after you replace the coin battery, also known as a “button”, “watch” or “button”, it could be due to an issue with the circuit board inside. In most cases, reprogramming the fob can resolve the issue. You can find the steps for the majority of vehicles on YouTube or in the owner's manual. It is possible to replace the metal clips that hold the coin batteries in the correct position. If they loose tension, it may prevent your battery from sitting properly, causing your remote to malfunction. In rare instances it is possible that the fob will become desync'd with your vehicle due to software or hardware issues. This could cause a significant trouble, but you could often fix this by visiting an auto locksmith to reprogram your fob for you. In some cases they may have to install the software again in your body control module too. Interference In addition to a dead coin battery the key fob could not be receiving or transmitting signals due to interference. This could happen when the keyfob is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons the key fob could not function may be a lack of connection to the buttons or damage to the internal chip or water damage. If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. You could have a malfunctioning 500 receiver module If you've tried replacing it with a battery, reprogramming it, or using an alternative key fob. The receiver module, located beneath the dashboard, receives radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets. Luckily, there is an easy method to reset all of the onboard systems in your 500 keys, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Then reconnect the battery. This will eliminate any residual electricity and restart the car's computers. This can help the key fob to function again. If the issue continues, you should consult a certified technician. They can diagnose the exact cause of your problem.